Chrysler and Jeep, Body ABS IPC and other Modules
C & e will only Program and or Initialize Chrysler or Jeep OEM Rebuilt or New
Replacement Body, Chassis and Suspension control systems Modules.
No Used or Aftermarket Rebuilt Modules, on any year of vehicle.
Warning;
Caution do not install any (Body, ABS, IPC or other modules) out of another
vehicle.This includes Aftermarket Rebuilt Modules. One ignition key on cycle
and other modules may reconfigure. These modules will now require
replacement, programming will not salvage them. Click on Critical Chrysler
and Jeep information link for year models and other details.
If replacing Ignition Lock assembly, click on Key Programming link for prices.
Note;
If you have a Chrysler or Jeep with a obsolete IPC, call AER Technologies
(a approved Chrysler and Jeep rebuilder).Talk with Jairo 714 446-8136
ask if they can rebuild your module.
All Year Models - All Modules
Updating to the most current Calibration and Service Replacement Programming.
2006 and newer vehicles $140.00
1995 through 2005 vehicles $125.00
Restraint (Air Bag) Modules, call for prices.
SKIM and WIN Modules call for prices.
Pre Programming Steps
When replacing the TIPM, call for special instructions. TIPM will be
damaged it they are not diligently followed. (IMPORTANT) call
Ken at 714 356-7481 before connecting the Battery with a new TIPM.
These are the Steps that need to be performed before calling C & e for a
Mobile Programming Secession! If the Steps are not performed and the
Vehicle is not ready for Programming a non refundable Service Call fee
of $90.00 will be charged. This fee will not be applied to any second Service
Call on this Vehicle. Click on Pre Programming Link. CALL for details if you
are not 100 % clear on any thing.
Chrysler and Jeep PCM ECM TCM MODULES
2010 and newer year models
Note;
C & e will only Program and Initialize OEM Rebuilt Modules on these year models.
Warning;
Caution 2004 and newer Vehicles may have CAN Networking, do not install
any modules out of another vehicle. This includes Aftermarket Rebuilt Modules.
One ignition key on cycle and other modules may reconfigure. These modules
will now require replacement, programming will not salvage them. Click on Critical
Chrysler Jeep information link for details.
Gas;
Updating to the most current Calibration, the PCM, ECM and TCM.$140.00
Service Replacement Programming, of a PCM, ECM or TCM. $140.00
OEM Rebuilt only.
Diesel;
Updating to the most current Calibration, the PCM, ECM and TCM.$140.00
Updating the PCM may erase the VIN requiring a Security
Pin Number from the Dealer. If C & e supplies the Pin number $ 25.00 *see note below
Service Replacement Programming, of a PCM, ECM or TCM. $160.00
If C & e supplies Security Pin Number. $ 25.00 *see note below
OEM Rebuilt only.
Note special steps must be followed on the Diesel vehicles listed below;
Ram w6.7 L
Jeeps w3.0 L or w2.8L
Sprinter w2.7L
1.When replacing the PCM the original PCM must be installed allowing information
to be stored "inhaled into scanner" then exhaled into new PCM.
2.Important, verify you can communicate with original PCM with a Scanner not a
Code Reader. If no communication can be established call Ken at 714 356-7481
before making a programming appointment.
2009 and older year models
Warning;
Caution on 2004 and newer Vehicles that have CAN Networking, do not install
any modules out of another vehicle. This includes Aftermarket Rebuilt Modules.
One ignition key on cycle and other modules may reconfigure. These modules
will now require replacement, programming will not salvage them. Click on
Critical Chrysler Jeep information link for details on vehicle models and years.
2006 through 2009 year models;
Gas and Diesel;
Updating to the most current Calibration, the PCM, ECM and TCM. $140.00
Updating the PCM on a Diesel may erase the VIN requiring a
Security Pin Number from the Dealer.
If C & e supplies the Pin number $ 25.00 *see note below
Service Replacement Programming, of a PCM, ECM or TCM.
OEM Rebuilt Gas $140.00
A Used PCM cannot be successfully OEM Rebuilt Diesel $160.00
Initialized in a Diesel. Used (Gas Only) $160.00
Aftermarket Rebuilt
If C & e supplies the Security Pin Number. $ 25.00 *see note below
Note special steps must be followed on the Diesel vehicles listed below;
Ram w6.7 L
Jeeps w3.0 L or w2.8L
Sprinter w2.7L
1.When replacing the PCM the original PCM must be installed allowing information to be
stored "inhaled into scanner" then exhaled into new PCM.
2.Important, verify you can communicate with original PCM with a Scanner not a
Code Reader. If no communication can be established call Ken at 714 356-7481
before making a programming appointment.
1995 through 2005 year models;
Gas;
Updating to the most current Calibration, the PCM or TCM. $125.00
Service Replacement Programming, of a PCM or TCM.
Used $140.00
Aftermarket Rebuilt
If C & e supplies Security Pin Number. $ 25.00 *see note below
Diesel;
Updating to the most current Calibration, the PCM, ECM or TCM. $140.00
Service Replacement Programming, of a PCM, ECM or TCM.
OEM Rebuilt $140.00
A Used PCM cannot be successfully Initialized in a Diesel.
ECM or TCM only, Used $160.00 Aftermarket Rebuilt
If C & e supplies Security Pin Number. $ 25.00 *see note below
Note;
Some OBD l, pre 1995 PCM Modules require programming. Call for details.
*Security Pin Code Note;
The quickest way to determine if a Security Pin Code is required on the vehicle
you are servicing, is examining the Ignition Keys. If the plastic head is 1\4 inch thick
and they look like the Ignition Keys in the picture you have a SKIM or SKREEM
Immobilizer System. Legally the Dealer in not required to give you a Security
Pin Code, but in over 10 years, in all but two occurrences they have.
C & e can provide a Security Pin Code for a fee of $25.00
Pre Programming Steps
These are the Steps that need to be performed before calling C & e for a
Mobile Programming Secession! If the Steps are not performed and the
Vehicle is not ready for Programming a non refundable Service Call fee
of $90.00 will be charged. This fee will not be applied to any second Service
call on this vehicle. Click on Pre Programmin Link. Call if you are not
100 % clear on any step.
Chrysler and Jeep Modules
C& e Auto Tech
714 356-7481
kenelliott@ceautotech.com
Go with God
C & e Auto Tech ©